--- In LINUX_Newbies@yahoogroups.com, "Paul" <pfrederick1@...> wrote:
>
>
>
> --- In LINUX_Newbies@yahoogroups.com, "Donald" <tambeaud@> wrote:
> >
> > I am trying to install a wireless adapter to my laptop. I am running Linnux Centos. My does not seem to recognized that something new it been connected to one of it's USB connector.
> > Don
> >
>
> Try uname -a to see what kernel version you have.
> Also check dmesg and /var/log/syslog to see if your system is picking up anything for the hardware. If it is then Google is your friend. Good luck!
>
Hi
The uname -a produce the following:
[root@localhost ~]# uname -a
Linux localhost.localdomain 2.6.18-308.13.1.el5 #1 SMP Tue Aug 21 17:10:06 EDT 2012 i686 i686 i386 GNU/Linux
[root@localhost ~]#
dmesg prpduces the following:
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9f3ff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 11000
CPU 1 irqstacks, hard=c0775000 soft=c0755000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.03 BogoMIPS (lpj=1662517)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9f3ff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08
Total of 2 processors activated (6650.30 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Using local APIC timer interrupts.
checking TSC synchronization across 2 CPUs:
CPU#0 had -1035531 usecs TSC skew, fixed it up.
CPU#1 had 1035531 usecs TSC skew, fixed it up.
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=136 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=176 bytes
migration_cost=46
checking if image is initramfs... it is
Freeing initrd memory: 3378k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
dmi type 0xB1 record - unknown flag
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1080-10bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 11) *4
ACPI: PCI Interrupt Link [LNKB] (IRQs *5 7)
ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 11) *3
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:00: iomem range 0x0-0x9fbff could not be reserved
pnp: 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:02: ioport range 0x1000-0x1005 could not be reserved
pnp: 00:02: ioport range 0x1008-0x100f could not be reserved
pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:03: ioport range 0x1006-0x1007 has been reserved
pnp: 00:03: ioport range 0x100a-0x1059 could not be reserved
pnp: 00:03: ioport range 0x1060-0x107f has been reserved
pnp: 00:03: ioport range 0x1080-0x10bf has been reserved
pnp: 00:03: ioport range 0x10c0-0x10df has been reserved
pnp: 00:08: ioport range 0xc80-0xcff has been reserved
pnp: 00:08: ioport range 0x910-0x91f has been reserved
pnp: 00:08: ioport range 0x920-0x92f has been reserved
pnp: 00:08: ioport range 0xcb0-0xcbf has been reserved
pnp: 00:08: ioport range 0x930-0x97f has been reserved
pnp: 00:0b: iomem range 0xfed00000-0xfed003ff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: ed000000-00000000
PREFETCH window 0x00000000d0000000-0x00000000dfffffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: ecf00000-00000000
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: e000-0000
MEM window: ecc00000-00000000
PREFETCH window 0x00000000e0000000-0x00000000e01fffff
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: ecb00000-00000000
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x79 set to 0x1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
type=2000 audit(1347043473.906:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key 8264E66E33BE4C73
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Disabling MSI on Portable Device
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1c.3 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (38 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: SONY DVD+/-RW DW-Q58A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 232k freed
Write protecting the kernel read-only data: 417k
Time: hpet clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xffa80000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 193, io base 0x0000bf80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 201, io base 0x0000bf60
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 209, io base 0x0000bf40
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 217, io base 0x0000bf20
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-5: new high speed USB device using ehci_hcd and address 3
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.12
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 177
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ata_piix 0000:00:1f.2: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 bmdma 0xbfa0 irq 14
ata2: DUMMY
usb 1-5: configuration #1 chosen from 1 choice
ata1.00: HPA detected: current 192426570, native 195371568
ata1.00: ATA-7: Hitachi HTS721010G9SA00, MCZOC10H, max UDMA/100
ata1.00: 192426570 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
Vendor: ATA Model: Hitachi HTS72101 Rev: MCZO
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 192426570 512-byte hdwr sectors (98522 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 192426570 512-byte hdwr sectors (98522 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
Initializing USB Mass Storage driver...
usb 1-7: new high speed USB device using ehci_hcd and address 4
usb 1-7: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: USB Model: DISK 2.0 Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 16035840 512-byte hdwr sectors (8210 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 16035840 512-byte hdwr sectors (8210 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.6-ioctl (2011-02-18) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2594l
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
type=1404 audit(1347043505.923:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
security: 3 users, 6 roles, 2161 types, 284 bools, 1 sens, 1024 cats
security: 61 classes, 85585 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1347043506.278:3): policy loaded auid=4294967295 ses=4294967295
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
intel_rng: FWH not detected
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:03:01.1 [1180:0822] (rev 19)
ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, low) -> IRQ 225
mmc0: SDHCI at 0xecbfd400 irq 225 DMA
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 177
eth0: Broadcom 4400 10/100BaseT Ethernet 00:15:c5:3e:ba:0d
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 177
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new driver hci_usb
input: PC Speaker as /class/input/input2
Floppy drive(s): fd0 is 1.44M
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26k-1s
iwl3945: Copyright(c) 2003-2009 Intel Corporation
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:0c:00.0 to 64
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Attached scsi generic sg1 type 0
iwlagn: Tunable channels: 11 802.11bg, 13 802.11a channels
iwl3945: Detected Intel Wireless WiFi Link 3945ABG
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1b.0 to 64
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device <unnamed> (046d:08c6)
input: UVC Camera (046d:08c6) as /class/input/input3
usbcore: registered new driver uvcvideo
USB Video Class driver (v0.1.0)
usbcore: registered new driver snd-usb-audio
phy0: Selected rate control algorithm 'iwl-3945-rs'
floppy0: no floppy controllers found
work still pending
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
work still pending
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Mapper loaded
input: Dell WMI hotkeys as /class/input/input4
input: Video Bus as /class/input/input5
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
input: Video Bus as /class/input/input6
ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
input: Video Bus as /class/input/input7
ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.6 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2097144k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2097144k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
Loading iSCSI transport class v2.0-871.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
libcxgbi:libcxgbi_init_module: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
libcxgbi:ddp_setup_host_page_size: system PAGE 4096, ddp idx 0.
Chelsio T3 iSCSI Driver cxgb3i v2.0.0 (Jun. 2010)
iscsi: registered transport (cxgb3i)
cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011)
Broadcom NetXtreme II iSCSI Driver bnx2i v2.7.0.3 (Aug 04, 2011)
iscsi: registered transport (bnx2i)
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
iscsi: registered transport (be2iscsi)
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8180 buckets, 65440 max) - 228 bytes per conntrack
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
eth0: no IPv6 routers present
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
usb 1-1: new high speed USB device using ehci_hcd and address 5
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new full speed USB device using ehci_hcd and address 6
usb 1-1.1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input8
input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.7-1.1
input: Logitech USB Receiver as /class/input/input9
inputhiddev96,hidraw96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.7-1.1
hiddev97,hidraw97: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.7-1.1
usb 1-1.4: new high speed USB device using ehci_hcd and address 7
usb 1-1.4: configuration #1 chosen from 1 choice
usb 1-1: USB disconnect, address 5
usb 1-1.1: USB disconnect, address 6
usb 1-1.4: USB disconnect, address 7
usb 1-1: new high speed USB device using ehci_hcd and address 8
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new full speed USB device using ehci_hcd and address 9
usb 1-1.1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input10
input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.7-1.1
input: Logitech USB Receiver as /class/input/input11
inputhiddev96,hidraw96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.7-1.1
hiddev97,hidraw97: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.7-1.1
usb 1-1.4: new high speed USB device using ehci_hcd and address 10
usb 1-1.4: configuration #1 chosen from 1 choice
[root@localhost ~]#
/var/log/syslog
[root@localhost ~]# /var/log/syslog
bash: /var/log/syslog: No such file or directory
[root@localhost ~]#
I am afraid that this is way beyond me!
Thank you for trying to help.
Don
VE3HOL
No comments:
Post a Comment